Search results

I installed a 3000 watt inverter utilizing the bow thruster batteries. Put the Xantrex unit under the port stateroom bed. Put the remote monitoring panel up below the salon carbon monoxide detector above the electrical panel. Went with the 24 volt unit. Have all 110 volt hooked into it...

I had one for about 10 years. Same year. Had ZF tranny and Vdrive. Never saw anything but that in any of the ones I had seen.

I have the exact same issue... 2003 480 Sedan Bridge. Happens with the salon AC duct work. Leave boat for week and show up on weekend to black foam particles all over the couch and table. Like the idea of a filter, but need to figure out how to take off cabinet structure around the duct work.

Called SeaRay and was told the porthole window is Bomar's part number S516-6SS-LS. Called Bomar (603-826-5791) now owned by Pompanette Group and they said most likely it is the gasket that has failed and leaking. Took off the retaining ring on inside of porthole and sure enough the leak is not...

Bump....anyone. These are the oval port hole windows in the staterooms and head showers. thanks. Dave

Anyone re-bed the oval port holes in the state rooms or heads? Have multiple ones showing signs of leaking. Couple have the dog ears broken off. Looks like the water is coming in from around the frame and not the window gasket material leaking. Any tips? Thanks. Dave

Best rates around back when I was shopping for my current boat. Global Marine Insurance 12935 S. West Bay Shore Drive, Suite 205 Traverse City, Michigan TRAVERSE CITY, MI 49684 (800)748-0224 globalmarineinsurance.com

I believe the drain hose comes from the overflow of the drain sump in the center hall way. This is the sump that all the showers and sinks drain into, then overboard. If the pump malfunctions and does not pump, the overflow will drain into that bilge area.

Yes. Exact same numbers as you stated. Engines do not like to run at that 1400 to 1800rpm range. More RPM means more air and cooler EGT.

Thanks, ttmott. If my rebuild shop cant find original I will buy this. Thanks. Dave

Anyone have to replace the remote start solenoid mounted on the starter? Do you know where to source and a part number?

I needed to purchase for the companionway head door. different door swing, but... Bought from fpmarine. Dave

Noticed this past weekend I have quite a bit of water gathering in the aft bilge area around the port rudder. Boat still on hard and have seen a ton of rain. I could see drips coming in from what I am guessing is the rubrail meeting the transom area and the vertical caulked seem of the transom...

I have a zinc on the crossover pipe. Not sure why you do not. I can tell you that the zinc is never used up and i move it down to the bottom one as those get used up each season. I also only have the one zinc for the gear cooler.

I also have installed the dual gauge to monitor both engines' EGT. Pretty straight forward. hardest part was snaking wires up to the helm. Use port on riser after turbo. Had removed old Clarion round remote control from helm and replaced with gauge. Used dual gauge by ISSPRO.

Very clever. I would be too nervous to drill into the muffler. Was trying to find ball valve small enough to replace the drain plug, but don't think I will find anything that small. Thanks for the reply.

Quality Time- Where did you put the ballvalves? Replace them at the drain plug? I was looking to do the same because of the mess when draining into the bilge. Dave

Thanks. I did call Sea Ray and they gave me part 750-SSID-10-120 and vendor of Ameritrade 888-870-4884. After calling them I need to verify the base part number on the unit, so need to go to the boat. Will take measurements, as you suggested as well. Thanks, Carter.

Anyone have to change out the hydraulic piston that assists the hatch going up to the flybridge? Opened it up this past weekend and heard hissing sound and oil all came out. Know a part number or vendor? Thanks, Dave

That was the beginning of my issue and now no worky.