Engine is definitely shifted into neutral. I took it out of gear before shutting off the engine. Just to be sure though, I shifted it back and forth a couple of times just now, no change. This is the carburetor model, with manual shift cables and throttle cables, if that makes a difference.
The...
Hi all. 1981 Vanguard 310 with twin 5.0s
I went through a lengthy process to get two remanned engines put in last year. Boat finally went back in the water last fall. Unfortunately, I travel extensively for work so this week is the first time I've been out to the lake to use her this year...
In looking around for info about my 310, I heard that they made a 360 Vanguard in the early 80s. Does that one you saw look like this?
http://www.searay.com/boat_graphics/electronic_brochure/company1729/1C1_27_74DERNJ51330.jpg
Re: 2015 Lake Erie CSR Rendezvous (Sea Ray New Year) Paper district Marina Sandusky O
Are boat-less attendees allowed? I'll be in the area but my boat is quite a long way south.
Any members here have slips in Fairport Harbor? I'm up here for work and yesterday I drove around a little bit, despite the nasty weather. I saw a few gorgeous classics docked along Riverbend and at HTR right on the lake. Hopefully none of them were bothered by the storm surge. I saw one small...
I've looked all over trying to find this info, with no luck.
I have a 1981 Vanguard 310 Express and I need to know the deadrise angle of the hull to order a thru-hull transducer. Stupidly, I forgot to measure it last time I was out at the boat. :smt021 I want to get it installed while the boat...
I'm looking for the shift levers and throttle levers for a 1981 310 Vanguard. I'd like to install original-ish parts if possible, but really any lever set that is built for non-electronic engine controls would work. My engines are inboards, so no trim switches needed.
Thanks for looking!
Evan
Thanks for all the replies and well-wishes! This is certainly an exciting project and I can't wait to get the old girl back out on the water. The old motors are coming out this week, so hopefully I'll have more pics to share soon.
I am going with a full MerCooling closed-loop system. My...
It has been an eventful winter/spring!
Recap: I purchased a 1981 Vanguard 310 in July of last year. The interior was in quite a state (tobacco tar stains on all the vinyl, interior hadn't been cleaned in ages, ragged carpet, etc) and the engines didn't seem to be quite right (~2800 rpms @...
I have a set of shutoff valves that allow both engines to draw off either tank, both tanks, or their respective side tanks. The valves are mounted on a panel in the center of the forward engine room bulkhead. Right between both engines. I open the center hatch to access them.
If you backtrack...
I've looked at the Seloc manuals, but they're all listed as stern drive model manuals. Would the engines be interchangeable?
I'll check for a Mercruiser manual on eBay.
Update:
I was out at the marina this weekend for a get together, so I didn't have any time to tinker in the engine compartment. But I did take a minute to try cranking the engine so my neighbor could hear what was going on in hopes of further diagnosing the issue...
No knocking! It won't...
Thanks for all the replies. Keep the advice coming!
I picked up this boat in trade for a vehicle I wanted to be rid of. I do love the classic design, and my family has history with Sea Ray (my grandmother used to work in the Merritt Island plant, where this boat was made). As a recent college...
Before the question gets asked:
No, I didn't have a survey done. Yes, I'm aware of the potential issues that no survey could pose. Live and learn, I guess.
H2ONUT: that was the price quoted by a local MerCruiser dealer. I have working transmissions and they're inboards, so no sterndrive to...