Search results

I don’t think the original blue/gold squiggle graphics are available anywhere so what has everyone replaced them with if you have? Other than a basic boot stripe, I don’t know what to do. My original graphics are disappearing.

Solid alarm just started occasionally when idling or no wake speed. Not the carbon monoxide alarms and the bilge pump has a different buzz. Outdrive fluid res beeps intermittently when low I believe and it has lube. Temp and oil pressure are good but I seem to recall each may have a second...

On my 99 270 it’s in the transom locker. If it shows the word “on” on the breaker, does it mean it’s on or I should flip it that direction to turn it on?

1999 7.4mpi 0L854*** 270 Sundancer single engine B3 Just before I was about to pull into the marina on plane my boat started sputtering and missing like it had water in the gas. I dropped it down to about 1k. It idled in running but a little rough. It smelled rich. It wasn’t until I got to...

Do you prefer putting the shift cable bellows on the transom assembly first and then feeding the cable through or do you prefer feeding the cable through the bellows not yet installed and then feeding it all through the transom, gluing and clamping?

My boat would not turn over when I went to start it the first time this year. I have power to the B terminal at the switch. I get power in the accessory tab. When I test the ignition wire when the switch is in the run position the voltage tanks on both the ignition and the battery side like...

For a '99 270 Sundancer with a single engine. I think my ignition switch/key has some internal corrosion. I think it has 4 terminals on the back and is the longer threaded plastic kind, but I have no idea if this is a replacement. The keys are not Sea Ray keys. I think it has 3 positions but...

I have a number of areas needing new caulk or sealant. These are not critical areas, but I want something that will last, not turn colors, and is relatively easy to work. These are not areas requiring 4200. The locations are things like where the cockpit seating base meets the cockpit wall...

I am looking at these 75-100w Class D amps from JL and Wet Sounds. I am leaning toward the 6 channel, played at moderate levels. My concern is this will be wired to a single 12v battery, probably a Group 27. The only other power draw on that battery would be the head unit. For those with a...

I need to do the steering shaft repair on my 1999 Bravo 3. The seal is now dripping. I know I need the JR Marine cover kit and wrench rental. Anyone have part numbers for the square shaft, bushings, seals, and any other commonly needed items? I did my bellows,etc. last year.

Is it still about 5:30 when looking down from the front? This would be from the factory.

My bimini poles have caps at the end where they pin to the boat. The mount has a rivet in the end cap with a wire to hold the pin. The wires are long gone, leaving a very sharp nib. If I drill out the rivet holding the nib, is the end mounting cap going to fall off? I just need to know if...

My '99 270 has one of those two foot tall Norcolds I think it is. Since we have had it, the super thin wood outer facing has been broken off. White or black would work. It is an odd design with foams strips between the face and the fridge, but the covering seemed like it was paper thin...

I was looking at a regular 10' dinghy with an inflatable keel and aluminum panel floor boards. The thing weighed 140lbs. Just how how much do those floor panels weigh? Most wood or inflatable bottoms I have seen weigh half as much.

I just did a full bellows, cable, trim sender job, so I was a bit concerned when I discovered water was slowly accumulating in the bilge. I would guess 1 to 2 gallons per week. It definitely seems to be from the steering shaft. The water is slightly orange, and on the transom assembly their...

I need to replace the mirror on my 270 Sundancer. I have no idea how to get any of the trim off or how to get the old cracked mirror off. Anyone done this? There is a 2 in panel across the top but I can't see how to remove it. The sides and bottom are also tucked behind the cushions and side...

I hate the diminished visibility while seated. I always stand with the helm seat flipped up. I got to thinking about this while trying to decide if I should put a wiper blade on. I'm not sure I could function looking through the windshield in the rain. (Cloudy eisenglass - rarely put it on)

The screen is clean. Is there a process for cleaning these things out or rebuilding one? It runs and vibrates, but won't pump water - no suction.

The outer edge of the largeclamp on my shift bellows I just replaced is about even with the outer edge of the underlying transom opening. It is glued, but should I move the clamp farther back or is that good?

My port side lounger has the end 3" verticle section that is shredded with cracks in a 1' section. I know it needs a new covering but the rest of the seating is fine. Does anyone know of a 2-3" wide vinyl tape in white that would make it through a season?