Need to replace fuel sending unit on '99 330 Dancer. Has anyone replaced theirs? Considering the newer reed switch vs the older arm float. Original pt # 1691486.
Anybody tried the Presta Hydroprotek yet. Long term results? Don't know much about the ceramic coatings products . If it seems too good to be true it probably is?
Last season I used Presta products for the first time. (Even though many threads had me leaning towards the Starke line.) After speaking with the Presta rep he suggested I use the Presta Gel coat followed by Presta's Maxfinishing Polish vs the Ultra Polish. Since you're also using Presta I'm...
Has anyone experienced any "yellowing" on their exterior seat cushions in the areas where two cushions meet, like in the creases where the back cushion meets the seat cushion? In a recent seat cleaning I noticed a definite yellow/tan color in areas not exposed to sun. I'm assuming it might be an...
Does anyone know the replacement model number for the transom hatch gas spring? I need to replace mine and I cannot find any model identification on it. It only shows the name SpringLift, no other information.
Spoke to rep on phone. He said that Pro Cut and Bubble gum are actually two separate one-step applications depending on the condition of your boat. If oxidized use Pro-cut then White Cloud Wax. If boat is in good shape then use Bubble Gum and White Cloud. Now I understand the skepticism when I...
Information on side of bottle says Cleaner/Wax also not to apply in direct sunlight? Did you ever apply outside? Have you done the Pro-Cut - Bubble Gum - White Cloud?
I know-I appreciate everyone's input. I'm sure I'm over analyzing this! Normally I'd already been done but my marina can't launch me till late May(long story) Thought I was switching to Presta this year then I saw all these posts about Starke and Smoove and others...Starke seems to be THE choice...
Is this the process you suggested since I only have the rotary? One pass with Elevate on white pad with rotary and then second pass with Ignition with yellow pad and rotary? Was there a significant difference when you hit it again with the forced rotation DA? Thanks
Looks great Ryan! I'm considering the same process however I'm not sure I'm going to start with Restructure but go to Elevate. Since you did Restructure and Elevate above your rub rail (and not below) I'm interested to know if you thought it was worth the extra step? Also, in your polishing step...
Contacted one of your associates re product recommendations. He suggested the Gel Coat on white wool with rotary followed by Maxfinishing with blue wool blend. (I'm not sure about HydroProk yet). I'm just a little concerned the Gel Coat might be too aggressive. I only own a rotary so he...
I do not own the Flex forced rotation. Is there a non-forced rotation polisher that you might suggest with the orange pad to remove swirl marks? Would a DA work or another type sponge pad on my rotary?
You used a DA orbital with a wool pad or a rotary? If DA what make/model because I didn't think the DA's were powerful enough for wool pads. Was it white or yellow wool pad?
Considering changing my compound/polish/wax process this year. Narrowed choices to Starke and Presta lines. I have a dewalt rotary and my hull is not too bad of shape that DON'T THINK I would need anything too aggressive like the Starke Level R or Presta Super Cut. I would appreciate any...
Do you only use Elevate now? (vs Elevate and Ignition) Do you do a two step process with Elevate- white wool followed by yellow? What's your pads and process?
What made you switch to Starke from Smooth? What type of machine did you use? Can't tell in the picture if that's a rotary or random orbital. You mentioned that you used pads and foam? 3"??
Thanks for all the help! I have the Dewalt rotary. I think it's comparable to the makita. Do you use wool pads like the softer yellow, green or blue or sponge? Does your process leave you will a good swirl free finish? I like what I'm ready about Presta. They claim their products don't contain...
Do you normally just use the ultra cutting cream or ultra cutting cream light. Do you finish with the ultra polish, like a 2 step process? Do use a rotary or random orbital buffer?