Search results

I replaced mine with one that looked like a marine one they were selling.g on west marine, but I bought it at the local tractor supply store for under $30 and works fine. Sent from my SPH-D600 using Tapatalk 2

Just about ready to head home fro our 14 day run up the erie canal to onieda lake from watkins glen ( seneca lake ) , my problem is that ever since day 3 of the trip where there was a lot of sea weed, my starboard eng is over heating at idle speed. I cleaned the strainer which haf a small...

Our marina is owned by a village municipality. It is also a.campground. Kids are everywhere playing and on bicycles. As far as kids on docks, its up to each and every parent to decide. Those are the stipulation of the marina. As for us we have twin ten year olds that grew up on water. They need...

Ok soo the problem has magnified!! We left for out 16 day trip and genny does not, will not start. It acts luke it wants too but just doesnt. Ive replaced the fuel filters and fuel pump. No luck . Sent from my SPH-D600 using Tapatalk 2

This is the old one Sent from my SPH-D600 using Tapatalk 2

Sent from my SPH-D600 using Tapatalk 2

I dont want 10% sitting around in the tanks either. Luckily tje station down the road aldo happens to sell non eth for around $4.00/gal. There has been an occassional usage of ethanol gas but if its not going to be sitting around eating at rubber and such there is no harm in it if its going to...

I have neen plagued with ac problems simce last season. My cruisair crapped out. The magnet was cracked and seemed as if the shaft that spun rhe mag was sligjtly bent. (mag would wobble on spin ) . WhT qould cause that. Last season was first wirh boat. I since rwplaced pump with what I thought...

Prices at all marins around here , Seneca Lake (a finger lake) are at $5.00/gal. Fortunately at my marina only, they are owned by the town, not private. Being owned by municipality we are the only marina on the lake where we are allowed to fuel our boats with our own fuel. I have 4 (15gL) tanks...

I tried lubing that end using lithium grease, also took apart rack and pinion and greased inside of rack housing. nothing worked. Its so bad my wife isnt strong enough to turn the wheel.. Sent from my SPH-D600 using Tapatalk 2

Hey thanks fot the tips. Much appreciated . Ill check out Amazon. Ebay had variouse teleflex sizes averaging around $140 _ $150 depending on size. Sent from my SPH-D600 using Tapatalk 2

Mine is soo tight im aftaid it will snap soon. Yes mine travels through bulkhead. I too scratched my head wondering how the hell to het it out and new in . Also my icemaker and sink are along the same side. It passes through bilkhead in exact spot as those. Any ideas as to drilling new hole with...

Sooo...my family and I are venturing out for our first 2 week long trip. We will be following my in-laws along the way as they have done this trip many times and know the way. Also they have 35 years boating experience. As excited as we are, I noticed my steering tightening up worse than last...

Sent from my PC36100 using Tapatalk 2 I have a 5k Quicksilver genny which runs fine. The problem is it won't shut off with either toggle switch. I have one one control panel and one one genny itself. I either have to use emergancy shut off circuit breAker tab or disconnect from battery. Is it...

Lol......exactly what it sounds like too. Sent from my PC36100 using Tapatalk 2

Now that I think about it when I was looking over everything before we launched, I did note to myself and my wife that the strut bearings didn't look healthy. Thought to myself they would have to be changed next season. Looks like it will be earlier than I thought. Sent from my PC36100 using...

Talked to friends who have 300 DA. They had same problem, symptoms as us last year with their v drives. Reputable marina diagnosed it as a strut bearing. They fixed it for $650. I'm hoping this is all it is. They had same issue down to the " T". Sent from my PC36100 using Tapatalk 2

Well..boat has been in for a week now. Enjoyed our first weekend on her. Downside.... Started to get gear clatter from port Hurth vdrive transmission. No clatter in nuetral, no clatter after I put load to it in forward at about 1100 rpm. It's even worse in reverse. Anyone with similar problem ...

I hAVE A quicksilver 5.0 by generac. I need to do maint on it. Possibly major repairs . Does anyone know where I can get a complete manual download ? does anyone have the manual they would be kind enough to put into PDF format for me ? I would greatly appreciate it !! I just put the 330 DA in...

Ok, so to those of you that responded to my post about radio install, Ty. I found a local audio dealer who also sells marine units . They also do site installations at a rate of 55 / hr. We found a resonable head unit that comes with up to 2 remote units. 1 for the helm and 1 for the transom...