Search results

does anyone know if the clarion wired control will work with a non clarion brand head unit? wiring appears to be similair/same

Anyone parting out a 98 sea ray I am looking for a rudder part #:604850 for a 330 sundancer

Thanks. Searay aftermarket manufacturers can't produce for ten days. Looking for one laying around the warehouse or on a boat that someone is parting out. I have calls in to sea ray warehouse , but thought of giving the forum a shot

Does anyone know where I can purchase a new of OEM rudder for a 98 searay sundancer? Thanks, adam 98 330 searay sundancer twin 7.4l mercruisers 310hp

Does anyone know where I can locate a new or OEM rudder for a 98 searay sundancer? Thanks! adam 98 330 searay sundancer twin 7.4l mercruisers 310hp

some good advice in there thanks. now i am concerned because i did not flush my cooling system after replacing a well worn impeller. same goes for the westerbeeke. looks like this will be my task this weekend! do you have any tips on back flushing the system with boat in the water? i will need a...

hi just read your thread on vibration. i have my 1998 330 sundancer in the water now and after sea trial today we noticed a slight vibration coming form what appeared to be the port side. we did hit a little shale at low tide a few days ago and am hoping that a bent prop is my issues and not a...

When I last used it last November raw water was pumping out the side well, but as you mentioned I'm sure it's toast now. Thanks for the help and advice

thanks! have any of you guys ran the generator whilst out of the water on dry dock? yep, i did, and it ran for 5mins then shut down, before i realized i potentially cooked it! i do not believe it is cooked as i it did restart but would only remain running if i held the pre-heat or choke button ...

Good reading the tips here guys. I'm about to flush my generator which is the 4.5w weestebeek model. It's tucked fairly tightly under the starboard side, and I can't locate the dam drain plug for coolant or the oil dipstick ! Any ideas what sides of the weestebeek I should be looking? Seriously...

can anyone steer me in the right direction to find service info on a westerbeeke 4.5kw model# 29339? i have searched online on westerbeeke.com and cannot find a 4.5kw jenny! i also dont understand why i have a pre-heat before starting for a gasonline powered boat/jenny? i am simply looking for...

thanks for that! i looked at the lines and connections and all seems ok visually, so if if the coils are cracked raw water would leak directly into the bilge im assuming. the amount of water was incredible! (3" deep in both bilge compartments) so it sounds more than likely this is raw water...

ok i just confirmed that water lines are coming from the AC unit under the V berth. one is the overflow that plumbs in to the plastic box/drain from the shower that contains a small pump with float switch. the other line goes from the compressor to a pump in the engine bay that is also connected...

thanks for you quick responses guys! to answer you both on the water lines, i have two white thick water lines running the length of both bilge compartments in the cabin. one comes from the bow direction (im thinking the heater/ac unit) and is routed into the plastic box that houses the bilge...

Hi all, i have had no replies in the 330 sundancer thread , so decided to try here. i not so familair with the boat yet, as i just purchased last thanksgiving, used for two weeks then winterized it. 1. where can i purchase either a oil pressure sender unit, or if this checks out to be ok, an...

larry, i have the identical 330 recently purhcased at marine max - Norwalk. i could use some tips on getting famaliar with my boat. 1. where can i purchase either a oil pressure sender unit, or if this checks out to be ok, an aftemarket oil pressure gauge similar to the factory installed one 2...

glad i saw this post!i also have fresh water in the bilge, and will check the ac (mine is inder v berth) connection. i have not run the ac at all, so dont understand where so much fresh water came from! both bilge compartments inside were half full!

PORT ENGINE OIL PRESSURE ISSUE can anyone direct me to a company that sells an OEM oil pressure gauge for a 98 sundancer ? Re. just before i winterized it the port engine pressure gauge was all over the place between 0-40psi. at idle it was bareley at 10. half throttle got us around 30-40. my...

mike, do you have any working oil pressure gauges from your 98? or, where can i purchase direct replacement OEM for my 98' 340? need a sender unit too I'm assuming thanks, adam 98' 340 sundancer

does anyone know of or have a good source to purchase a quality used dinghy's? this would fit a regular swim platform on a 330 sea ray, and i will prob go with the nautley mount if i can locate one too. thanks