Search results

  1. 4

    Source for Chrome Cabinet Molding

    http://imgur.com/sFgyUut I'm looking for the L-Shaped molding found on the bottom of the galley cabinets in my 390MY. Anyone ever source this stuff? Thanks,
  2. 4

    2005 Vintage Electronics for Sale

    I just replaced most everything on my boat. The boat has less than 300 hours of run time and the electronics are in great shape cosmetically (include sun-covers etc) and are fully operational. These would be great for someone who doesn't want to replace a the rest of the system just because a...
  3. 4

    Cracked Faux Porthole Window

    Hi Guys, Has anyone ran into this before? The window is cracked in two places, allowing water into the rear bilge. It appears to just be black plastic. This "Window" is merely to maintain symmetry and not a real operating window. It's on the Starboard Aft of the boat and will require the...
  4. 4

    Full Plotter, Radar, Sounder Upgrade

    Hello All, I'm looking for advice on upgrading the marine electronics on my 390 MY. The existing panel has a C120, 4kw Open Array, and ST7001+ AP. I’d like to keep the ST7001+ so whatever I purchase will need to be compatable. That said I want to AVOID RAYMARINE. Their support...
  5. 4

    Leaking Shower Sump - PVC to Sump

    Hello All, My 390 MY uses a PVC grey water system that drains into a sump. The sump seems to simply have a hole cut in the side that the PVC main drain line comes through. The only seal seems to be some material packed into a cone on either side of the PVC "sealing" it to the HDPE sump...
  6. 4

    Pigs on a boat

    One of you finally did it didn't you? Sent from my iPhone using Tapatalk
  7. 4

    Generator on Swim Platform and AC Install

    I know this has been a hotly debated topic! Can anyone say if this is a safe install? Sent from my iPhone using Tapatalk
  8. 4

    Cruisair R417a - Evacuate and Recharge R22?

    Hello, I have a split system (FX16C-P/M188-417SMX) that cools my bridge. The Condenser is marked R417a, while the air handler is marked R22. I had a local HVAC guy out and the system is totally empty...we're pretty sure the leak was at one of the flare connections. My problem now is R417a is...
  9. 4

    Holding Tank Sensors...Replacements, Upgrades?

    Well I've discovered mine are shot...not fouled just flat out not switching anymore. This design just seems terrible to me...has anyone used an external sensor with success? I'd like to use the existing wiring as it has a gauge in the panel (Empty, Half, 3/4 and Full) as well as gauges in each...
  10. 4

    Davits for High Platforms

    I just got finished installing a Swimplatforms.com extended platform in my 390 MY. Now that the boat is launched I know it's 24" from Top to Water. Does anyone have a suggestion as to what type of Davit would be best for my Rib? I made a set of davits for my Formula that were similar to Doms...
  11. 4

    Hardtop Strength? Polishing/Waxing?

    Hello All, I'm just wondering if anyone has an idea of the strength of the hardtop on my 390 MY. I've seen people standing on Sedan Bridge hardtops and they aren't as well supported (no windshield frame) as the Motor Yachts. Is it OK to put my weight on it to polish and wax, change antennas...
  12. 4

    Replacing Windshield Seals - Motor Yachts

    Hello All, I've managed to track down and purchase all the exterior windshield seals as well as screw covers for my 390MY. The old ones have shrunk and pulled out in the corners or are exposing the track. It appears to be a simple cut to length and press in job. However, I have a few...
  13. 4

    Autopilot Questions...

    Hello I'm looking at doing an electronics upgrade and am wonder what I can keep from my existing autopilot system. Its a Raymarine ST-7002+ from 2005. I know it has Seatalk and Nmea 0193 inputs. I'm going to replace the pair of C120s, Open Array Radar, Sounder, Transducer. I'm not sure I'll...
  14. 4

    40MY/390MY Measurments

    Hello, If anyone happens to own a 390MY/40MY and be onboard...would you mind measuring the space opposite the washer/dryer under the galley stairs? Stringer to floor, opening width and depth would be great. Thanks!
  15. 4

    High Water AC Pump Cutoff

    I've read one too many stories about AC Lines, Fittings or Pumps flooing or skining boats and got to thinking. Why isn't the high water alarm(s) tied to a latching relay that kills the AC pump? Most of us leave our units in humidity control mode while away, meaning the pump will run! I'd much...
  16. 4

    Calling all 480CE Owners

    Hello, I'm looking at a 480CE powered 390 Motor Yacht. I've read a few horror stories on dropped valves, failed valve seats, totaled motors due to over loading/propping. I'm curious how many people here have had their props tuned or changed entirely to reduce engine load? The boat I'm...
  17. 4

    Diesel Survey - Michigan - Advice Please

    Hello, I'm working on purchasing a new to me boat, this time with Diesel power. The boat is in Harrison Township, Michigan. Having Cummins come out to do the survey is one option, but I thought I'd see if anyone had other advice? I know sometimes an independent know it better than the...
  18. 4

    Harrison Township/St Claire shores - Surveyor Recommendation and Broker Warnings?

    Hello all, Can anyone suggest a good surveyor in this area of Michigan? Also, are there any brokers or companies I should be cautious with? (Probably best to communicate this one through PM) Thanks!
  19. 4

    390/400 Motor Yacht w/ Hydraulic Platform?

    Hello All, I'm looking at a 390/400MY with a Hydraulic Lift Extended Swim Platform. This doesn't seem to be a common option and I'm concerned it's too heavy for the boat and will affect performance. It's powered by Cumins 480CE. Any advise is appreciated, Thanks!
  20. 4

    410 Sundancer (2001-2004) Aft Berth Size

    Hello All, Short Version - Does anyone have dimensions on the rear berth in a 410 Sundancer? Long Version - Our 34 Formula is sold and we're looking to go bigger. A 2003 410 w/ Cat 3126's is on our short list, however the rear birth size is important. Does anyone else have advice or...
Back
Top