Hi:
I have some paint to remove. I don't know what it is but I think it's alkyd enamel.
MEK-based stripper didn't work well at all.
Seeking your expert advice.
Thanks,
Jeff
Hi:
I bought my 1977 SRV 240 Weekender last year to fix up. Target first launch Spring 2012. It has a MCM 260 Mercruiser 350 small block, Alpha drive and a displacement of 4400 lbs.
It came with two props:
Aluminum #48-78118-17
14 1/2 " 17 pitch
SS- 48-88438A4 17P
15 3/4 17 Pitch
The...
That's good to hear MM. Thanks for the reassurance. I practice good maintenence on my machinery so I'm looking forward to some relatively trouble free trailering once I get this trailer roadworthy.
Jeff
I removed both bellows from the top of the Y pipes and there are no shutters there. I think on an old engine like mine (1977) they are way down deep in the y pipe. I don't have my service manual yet so I can't be sure.
Jeff
Thank you everyone for all of the vaulable advise. From what I've read here and on other forums getting from point a to point b with a trailer without problems is kind of rare.
Anyway, the frame plate with all of the specs for the trailer has long since faded away. The tires on it look bad...
Hi Ken,
That's a scary thought. I think my shutters are not servicible unless the engine is pulled. Yikes!
I guess I'll start figuring out if I can diagnose if that is the problem. I don't have any clicking noises. Other than that I don't know what to look for yet.
Anyway, this old boat is...
Thanks for the follow-up info. I definitely can't keep my hand on the manifolds. I will start checking into the pre-detonations thing in the spring. That sounds like a good lead. Thanks.
In case you missed my original posting, the risers and manifolds are new this month. They have zero hours.
Jeff
I'm planning to replace 4 rotten trailer tires next spring. I bought the old Load-Rite galvanized double axle trailer and it came with F78-14 ST tires. I forgot to check the load rating. I don't know if they are the right ones or not.
I have '77 SRV 240 WE that is listed at 4400 lb...
Thanks for even more great tips. The problem appears to be solved.
I didn't get the picture of the T-stat housing but it soen's have a "T" set up. I looked up a picture on line of that type.
I removed the Tstat. It was installed correctly.
I proceeded to remove the Tstat housing. there are no...
Thank you to everyone who is making suggestions.
I'll try and get a picture of of the T-state housing next weekend.
The stat is definitely in correctly.
I do plan on testing the t-stat in hot water. I took a chance that being brand new that it would function. Maybe I lost that gamble.
Circ...
Hi:
I'm working to get my recently purchased 1977 Mercruiser ready for next season. I've never launched it.
Engine is original raw water cooled MCM 260. It spent most of its ife in fresh water.
I just replaced the manifolds (date marked 1982), riser elbows and thermostat. All new gaskets. No...
Hi:
I'm working to get my recently purchased 1977 Mercruiser ready for next season. I've never launched it.
Engine is original raw water cooled MCM 260. It spent most of its ife in fresh water.
I just replaced the manifolds (date marked 1982), riser elbows and thermostat. All new gaskets. No...
Hi:
I just replaced the manifolds and risers on my 350 mercruiser. I torqued them at 30 ft/lbs by mistake. The service manual I have says 20 ft/lbs for the manifolds and didn't specify the risers
Should I:
A. Back them off and re-torque at 20, or
B. Not worry about it?
If I do back them off...
Hi ,
I'm replacing the two batteries in my new-to-me 1977 240 weekender. It has a 260 Mercruiser. When I got it it had 2 type 24 starting batteries. Is it ok to put one starter & one deep cycle in? Do I really need a starter battery or could/should I go with two deep cylces?
There is a battery...
I just bought a 1977 240 weekender with 260 mercruiser that I haven't run. I'm not counting on it running but I'm hopeful!
PO reports that it ran good wen it was winterized & stored 3 years ago. It has about a 1/2 tank of the 3 year old old gas in it.
When Spring comes and I start it...
Now that I have my new old boat home I'm starting to try & figure what works and doesn't
The bilge pump toggle switch on the dash board has three positions.
Down- the aft bilge pump goes on
Middle- nothing happens. Off or auto?
Up- nothing happens. off or Auto?
Midship bilge pump (under the...