Hello: There, i have a 300 sedan bridge and i replace the carpet with allure from home depot. I just cut the carpet with a blade khife and leaved thecarpet under the cabinets. there are mani modification on the 300 treats. good luck: jorge
Rick, Welcome to CSR, My is on the floor in the center compartment. I personaly like the idea to have it on the engine room , not in the salon also it will be great to have a gas tank for the gen. like Tom.I have two PO so can not tell.good luck : Jorge
looks great ! what did you use on the trim for the hacth on the floor ?
I just did mine with allure and have three hacth on the salon together.
need help on that:smt100
thanks in advance
Hellow there, Great inf. thanks for your time looking foward to see the other chart as it go up:thumbsup: . this way we can safe fuel goin at lower speed.we are at $4.19 per gallon this weekend. i been goin at 2000 rpm to safe fuel and enjoy the ride to the beach. i just did the allure floor...
looking good , I remove mine about 4 years ago and you can see the marks of the stripes at a close view, they wont go. But it will look longer with the stripes.
i may put them back only on black 2" with out the gold. good luck:thumbsup:
Ummm, I was afrait it wont fix the cabin door. But its great idea to separate both engine & mass.
I may use allure on the floor. they haved on home depot... thanks a lot .
Jorge:grin:
Hello: there,
Long time no enter to the forum! I have to replace my onan genset and y bought a westerbete used . Have no idea how to remove the floor over the genset the previous owner make so modification on the floor making it one lever and no
space to taker out. Have you guys did this yet...
Hi: There,
you just have a great boat, they go the same from 1985 until 1987 y do have the same model , and keep fixing on the way we use every weekend. love to see your pictures keep posting please.I like the idea to have the holding tank on the engine room like your ,mine is inside the cavin...
that was a great choice you made. new is new you will have no complains , I have a great experience with them evendought is litter more expensive you will like the up-grade. good luck...:smt038
Jorge
Hello: There,
I use Michigan motor four years ago with a new long block. Great service even the spark plug where on!
no complains. last year I use Rapido Marine for the cheap price on a remanufacture long block. to make a long story short the heads where bend so it burn the head gasket on the...
hellow there:
not impossible to do , very important to cut the current of the battery before. And the positive cable have to be insolated just as a precaution. If is there for a long time you will need a hamer to lose it from the engine with movement all around. you can do it just need time to...
Hi, There i have a 300 sedan brige 1987 and it use 1"1/4 inch on the shaft. for the zink plates they have few size take the used one to the marine store near you..
good luck!
Jorge
Hi: you will need to use many parts from the damage engine to make the one from the truck to be marine. its not a drop off. verify how much it will be to buy a remanufacture one. just dont use ( Rapido-Marine ) I personaly have a very bad experience. the engine block and heads will work also the...
Hi, there i am looking for the same bulb on the anchor & tramson the saler of the store on the marina explain to me if i was goin to used on the allwood the one i have i will need to make an spacer to fit the bulbs.
as i dont like the idea so just looking for the best price to get the whole...
Hi! Capt.
You better start to verify if there any current or 12volts, on the positive and if you have a good ground on the bars. also usually on the swicth on is up & off is down. i have a 300 1987 sedan brige and i get the schematics from a searay club menber it may not be the same diagram but...
Pack : nice job, did you have to know what size are your propellers?
i replace mine to 3 blades 17 x 15 but not geting to much rpm.
Thanks in adavance.
Jorge