Search results

my boat came with the hardware, minus the actual arms, so if you have some just sitting around, maybe you might want to sell it. thanks

I cant even get them to answer the phone??? nor will they return any emails. My boat came with the mounting hardware but is missing the rest. i was hoping they could sell me just that portion. i guess i'm just stuck patching the holes and going with a differrent vendor. pretty sad when you...

OK, after further reading I think the lightly engraved "L" at the end of the part # means "cupped".

thats the confusing part. its engraved with a part #, and then a lighter L is stamped at the end. but its clearly not a left rotation prop. I would end up ordering the wrong prop.

i just put some led lights back there in the dash area and hold them in place with wire ties and it lights up the row just great now.

I must have hit something because all 3 blades on my port rear prop are cracked. the repair shop (thepropshop.com) said its not repairable. my question is, the front prop is supposed to be left hand and the rear prop right hand, correct? My rear prop has a L stamped at the end of the part #...

boy this confusing. So I only need the standard ones. of course after the parts guy told me i needed the 3 wire ones, so i went and bought them elsewhere, since he didnt have stock. How do I tell if there good or not, is there a way to test them? I've tried playing with the calibration and...

Also, can someone please look at their boat if they have a smartcraft - bravo 3 set up and tell me if they have a 2 wire or 3 wire trim sensor on their bravo 3?

I'm pretty sure its a stock set up. i just googled amberjack 2003 290 smart craft and they all have it on the ones for sell. plus the 2003 brochure says its standard equipment. apparently the Amberjack got special treatment :) All I did is unplug the system view and plug in the vessel...

double post

I just bought a 2003 amberjack 290 with 5.0 mpi's with bravo 3's there is no trim gauge. its supposed to go through the smart craft i guess. first thing i did is upgrade to vessel view. However, the trim does not work on the smartcraft. after investigating i determined that each has only 2...

Has anyone replaced the Kiss Stove? I tried mine 2x. once on first day, worked fine, so i took out the new tank. then this weekend while camping on it. could hear it leaking butane while trying to get it hooked up. finally quit leaking so we thought. turned it on and in about 10 seconds...

thanks, just ordered the atwood. I found a old archive where someone mentioned a bed extension somebody made? anybody on here the person who made it? I would love to see pictures. its the only thing i dont like about boat. the bed is just 8 inches to small. made worse by the foam padded...

Hello amberjack owners Wish there was more action on this site for these 290's because I just bought a 2003 with 5.0mpi and bravo 3. Im going to have lots of questios. First one is with the smartcraft should these have 3 wire trim senders instead of the 2 wire? Mine has the 2 and on the...

thanks, i found that either my ground wire is bad or my ground on motor connection is bad. however, i cannot seem to get the bolt off. so temporarily i have ran a 2nd ground from bank 2 to bank 1(since its ground is good). at 7$ a foot that 8ft run is expensive temp fix when only 2 ft is...

my 96' 240 has 2 banks, 2 group 27's that are deep cycle. and # 2 bank has a group 31 starter(brand new from costco, mfg by johnson controls). The group 31 marine starting battery cranks the the motor, but it seems like it is struggling. If i put it on bank 1, with the 2 group 27s from 2010...

turns out I had a bad orange wire on the starter and when i pulled on it it broke off the spade. what threw me off is the volt meter at the dash reading 14V on bank 2, but only 12V on bank 1. seems like i should have had a problem no matter what bank was sending power to the starter. my...

I bought one of these today and it says the batteries are low but good. http://www.amazon.com/gp/product/B000K38UN6/ref=oh_details_o06_s00_i00?ie=UTF8&psc=1 So traced out the system better. the on board battery charger is only hooked to bank 1, xantrex freedom 10. when plugged in it is...

I need some ideas on how to diagnose an electrical problem that just started. when running on bank 1 the alternator wont go above 12.5 volts or so according to dash. but when i switch to 2nd bank it runs at 14v. So i think i can eliminate the alternator as the problem. I have 2 banks on a...

I want to own a spare prop, and since i'm looking to buy, I want to get the best prop possible and use my current as the spare, which works fine for the most part. I'm leaning towards the revolution 4, for good hole shot and overall performance for these heavy little boats. current prop is a...