Search results

  1. D

    Sender unit

    Anybody help me with where to locate a sender unit for 100 gallon tank 1996 Sundancer gasoline
  2. D

    Travelers yacht insurance

    Has anybody had their rates jump excessively over last couple years ?? Mines raised over 200$ since 2019. There have been zero claims . I've thought about searching for new insurance, but been with them twelve years . Thanks
  3. D

    New exhaust elbows

    So I got an updated set elbows that replace the old style on my 96 7.4 .Mercruiser tech gave me part number . Problem is my boat use 3 inch riser block between elbows and manifold . Plus old was fastened with studs . New one are about 6” bolts . But bolts need to be about 10” to use riser...
  4. D

    Replacement elbows 1996 7.4

    Anybody have a cross number for #816900-C?
  5. D

    Going to take a gamble

    So I developed a exhaust pop through carb at 3300-3500rpms. I back off throttle clears up. First thing came to mind was I crapped a flapper valve . May been lodged in exhaust . After tearing into . I have water puddling front of #5 cylinder in exhaust manifold. I changed riser spacer block and...
  6. D

    Fly fish carburetors

    Anybody have any feedback of flyfish carburetors? Think I’m going to order one
  7. D

    Intermittent hesitation high end

    7.4 carb . Coming down on plane high side of rpms get a miss. Idle, no wake speed , low, mid range boats powers up great! 4 barrels opens and fuel spraying nice. New fuel pump and separator . Didn’t help. Going to throw money at full tune up cap rotor etc. Just seems weird high end rpm only miss...
  8. D

    Orange alternator has 12 volts ???

    I seen orange wire on alternator need a new crimp end . Old one had been hot . Just thinking old , I’ve owned boat 11 years . I installed new one . As soon as o fired motor. Orange wire heated up like direct power ????. I killed battery switch. With orange wire disconnected from alternator it’s...
  9. D

    Adujusting B3 top side shift cable

    Any way to adjust top side of shift cable without bravo tool ?
  10. D

    Mechanical fuel pump part number

    I have a 96’ 7.4 bravo 3 drive 270 Sundancer . Need part number for new mechanical fuel pump mounts to water pump housing .Thanks
  11. D

    Replacing lower shift cable and boot B3

    Question. How much hard sheathing housing sticks thru boot. My cable doesn’t have a mark as some I’ve read about ..Thanks
  12. D

    Bravo 3 shifter cable adjustment tools

    Can anybody tell me how thick plate at bell housing is ?? I think 1/4”
  13. D

    Transom bolts

    needing the 2 rubber washer gaskets for lower acorn bolts alpha early bravo transom bracket. I can find bolts does anybody know if they sell just gaskets ??
  14. D

    Using 3m premium marine filler.

    Doing some searching .Helping buddy with blisters. The way I’m reading info on this stuff repair boat. Then just re apply bottom paint . I told him to buy some gel coat . If it doesn’t match close doesn’t matter then bottom paint . Bottom paint being used is interlux nt
  15. D

    This Would’ve sank the boat !

    So as some know I found my slow drip leak. It was confirmed when I pull motor. One flange on y pipe was broke off. I figured while I’m here age of boat I’m going to replace transom seal coupler etc. This hole is a little larger then first seen as I wire wheeled it got larger. I’m guessing...
  16. D

    Found my leak! Next question

    Ok it was my y pipe as I suspected . Upon removing motor one ear was broke off? Not sure how that happened ?? I’ve found a like new y pipe.Are they the same? The 4 bolt flange is same and they measure same width. it’s a little older. It’s off a 1992 small block. But it does have different...
  17. D

    Socket size coupler hub 7.4

    Going to pull my engine this week at remote location going to pull coupler hub off engine to put motor on stand just wanted to make sure irs not a weird size socket 12 point head bolts on coupler can anybody tell me the size of the socket I need to pull coupler off motor . Thanks
  18. D

    Checking y pipe leak

    I know wether y pipe or transom seal I have a leak. Seems like y pipe about 2” away from transom .Ive been told the pipe will leak with water muffs on garden hose ??.Can anybody confirm please. Just doesn’t seem like enough water compared being in the slip.Thsnk you
  19. D

    Looks like got to pull motor

    Just wondering if carburetor flange can handle pulling motor ? Or need to used longer bolts corner to corner on intake ? It’s 7.4 and it will have manifolds still on but not risers . Seems to be leaking at y pipe flangeWater dripping onto power trim lines. Anything visual I can see it’s not...
Back
Top