Search results

OK Donnie, here's the deal. You're only a few (5 or 6) hours from Dallas. Why don't you come down at the end of summer, pretty-up my boat and I'll treat you to a couple of nights in a hotel and pay you for the work. We can even time it so the boat is out of the water when I have it pulled for...

Does anyone know what the thickness is of these panels? Thought I would ask the question here before taking the door off. Would 1/8" be too thick?

Thanks for the reply and the caution regarding the vinyl. Since I did use some PolyGlow in an area that contacted some vinyl striping, maybe the best choice is to go with the cleaner that came with the PG kit. If that doesn't get it all then maybe a floor wax remover. I think I read that...

Glad I found this thread. Anyone feel free to jump in. I've had my 310 Sundancer since new (10 1/2 yrs) and it has always been in a covered slip. I have been struggling a little the past 3 or 4 years with getting that new mirror finish back and am ready to try anything. I did the PolyGlow...

Take a look at http://www.fpmarine.com Better yet, give them a call and talk to Ken. He stocks a good amount of Sea Ray (and other) stainless hardware. I just changed-out all of my plastic Southco slam latches for stainless. He's got pretty good prices.

Try this.... http://www.ryderfleetproducts.com/cgi-bin/ryderfp/products/product_detail.jsp?BV_SessionID=@@@@0092388276.1244916122@@@@&BV_EngineID=ccceadehgmhfjkgcfkmcgfmdfoldflm.0&oid=45683 $6.59 for the assembly, not just the blade. I ordered online and had in my hands in two days. This...

Here is a link to your wiring schematics. http://www.searay.com/owners_manuals.asp?tab=&year=1997&folder2=95_99_330_Sundancer

First, check the fuse in the charger line to the port battery(s). It may be blown and the batteries are just draining down. That actually happened to me recently. Second, I'm not so sure Sea Ray would have wired those in series. More likely they are in parallel which maintains 12 volts. Do...

That's exactly my point. I've got mine 6 inches from the battery post. I've also just installed a new Pro Mariner charger and think that I'm going to spring for their monitor which simply plugs into a connector on the charger and gives you individual bank status. My problem all along has been...

Good post. I just went through a complete re-do of that circuit including new connections and fuses due to the same issue of not knowing when the fuse blew. A couple of things. First, the fuses are FNM (Fusetron) 30 amp and are commonly found at Home Depot and hardware stores. I think they...

I have to agree with the PK comment but unfortunately it's a two hour drive for us. We have been at Pier 121 on Lewisville for 11 years with no plans to leave. The 12 minute drive from our house is the primary reason. It's not a beautiful lake but it is what it is. I grew up in Austin...

Actually that was the last communication I had with him earlier this week. I set the switch to 5 for AGM 2. That seemed to be the best match for the Optimas. On the subject of batteries, I recently bought a private label Odyssey for one of my vehicles. It is a Sears DieHard Platinum PM-2...

Now that I've got the ProNautic 1240 installed, I thought I would post the results and some opinions. First, my set-up is (3) Optima D34M Blue Tops. Two are wired in parallel for stbd engine, house and gen. The single is for port engine. So essentially a two-bank set-up. This is on my '99 310...

I appreciate the feedback. I have actaully considered most of the points brought out here, even yours Blue Eyes.... :grin: As I said, the a/c is still cooling the cabin and while everything is running fine, it's the noise factor that leads me to believe that the compressor is nearing the...

Have owned my 310 since new (1/99). Even though the a/c still works, the compressor is getting louder and louder (either that or I'm getting more sensitive with age). It's a Cruisair 10K btu reverse cycle and is installed under the forward berth so sleeping is difficult. I have checked the...