Search results

It was leaking from the compression fitting on hose I bought new that goes from carburetor to separator fitting. That is a male or concave compression fitting coming out of separator. The hose end is female compression convex. I tightened the dam nipple on separator so much it cracked the...

yes like stated above on the transom back starboard side usually will tell year of boat

OK so I put electric on it and the coast guard approved line that I bought could not keep it from leaking. Teflon paste blue black all fuel rated sealants no luck kept leaking. So I thought pushing fuel thru separator was the issue but it was not. I went old school bought brass fitting cut the...

awesome thanks Mike

Hi guys I have a 1986 300 weekender velvet drives. While I was fixing boat I stepped on that heat sensor that comes off the top of trans. Does anyone know the part number or if they are specific sensors for them. I found this one for 70 bucks seems like it is what I need Any help thanks Marty

great advice Dave I will add when I bench tested the old pump could barley actuate the arm . I suspect the pump seized up causing my problem. Old pump is out and made block off plate gonna try it all out today fingers crossed. I will update Thanks for the help Marty

Dave I really appreciate all your input . Don't mean to come off as challenging you just merely reinstating what I have done. So to clarify I had problem few weeks ago totally agree never seen this happen either bent yes. But my problem is 1) I hooked a outboard hose to tank got good gas and...

THANKS FOR YOUR INPUT DAVE BUT BOAT RAN GREAT FOR 14 YRS. It failed other day on a Tournament day the push rod shows wear and new one was only .05 longer. Not enough to push rod the lobe on cam is worn I suspect. Without pulling motor I cannot tell for sure but all points in that direction. So I...

the parts manual for trans to big give me a email I will send it

too big

Here is what I have and trans if velvet

still shear I believe you can do from bathroom taking access door off

ok so on further investigation specs for O/A length of fuel push rod should be 5.75 mine is missing .200 on fuel armature so any idea as to why or being that Harding of pin may have gone .030 deep of penetration it failed for what ever reason. DO you think if I put new rod in I will be fine cam...

I hear you guys that is why I asked the boat for 14 yrs has been maintained that I have owned it and previous owner. It is very clean boat inside and out. Motor maintained run great 1300 hrs not crazy on hours for year it is. I think I may get 2nd opinion on it. Thanks for the input

update so I got a boat macanic to look at boat he tells me that cam and push rod that controls the pump that lobe is shot. Now I don't doubt what he thinks is wrong with it. But it ran and still runs so good if you pour gas in carb. SO my problem is if I put electric pump on what are thoughts on...

Well down for a few days cut the hell out of leg last night 6 foot drop down to boat from docks wind blowing so damm hard here blew all water out. 10 stitches later I will see what I can do tonight. Bill are you talking about a check valve on tank. I don't know about a anti siphon valve may be...

I did fill on new filter but thanks. Just thinking here at work so when I took hose off after 1st filter the one directly off the tank. Then stuck that right in can with gas it should have fired. To rule of venting problem Now only other thing is I did not reinstall the clear or yellow tube for...

I will check vent thanks for that great tip that's why I love this site. The filter/separator had a full filter of gas when I took it off. After dumping out to check for water. I installed anew one and it has never filled up again and 1/2 tank of fuel. The paper one bye the tank was wet but no...

Hi guys really at a loss here. I have a 1986 300 weekender twin 350 cui. The starboard motor started running ruff on way in to port last weekend on fishing tournament. Came thru channel ok then went to dock motor shut down. I cant get fuel up to carburetor now I do have spark. Did all the likely...

JB WELD WORKS GOOD ALSO