Search results

Thanks, Purchased a 310 SunSport, Problem is the hatch lifting mechanism only lifts it a few feet or so and unable to get in to service the engines. There use to be an extender bar bolted on the end of the cylinder that gave it another couple of feet. Due to some recent servicing it's come up...

Thanks all, I'll check on another site....

1993 Sea Ray SunSport 310. Wonder if anyone can assist or point me to the correct forum. Had some work done over the winter and now the electric cylinder only opens the engine hatch a few feet. I haven't used the boat much this year and was told there is a part missing. The mechanic is no longer...

Well I've flogged that one to death. If anyone has had moisture at the headline in the vee berth area it comes down on the sides and it's difficult to clean the stain off so I have to figure something. I'll check around and find what the material it is and how to refinish it and report back if...

Boatman37 we both have the same winter project. I looked at a picture of your style of boat and in my case which might be the same system as yours you removing double machine nuts every couple of feet or so and the trim should pop right off. I notice a forward piece of trim that runs across the...

OK - Well, can anyone tell me what material the side wall covering in the vee berth is make of. The material that covers the side wall above the shelf to the head liner. I need to clean it and not sure how to remove it and it feels like it's a soft wood or board material that might get damaged...

That's a good one, I'm not quite sure how to remove above the shelf line to the head liner in the vee berth. It seems like its glued in position and I'm worried about damaging it. Maybe someone else can suggest a removal procedure or even what type of board it is! I have found that a cleaning...

Need to recover the vee berth cushions due to wear and clean the head liner and freshen it up some how. I would like to read the link you mentioned on how to remove this head liner when you have a minute. Many thanks, Dave...

There are Philips screws behind the buttons. As I am reupholstering I cut across the button to expose the screw but is not necessary as the screw is close to the button. If your taking off the trim at the shelf level let me know as it is a different procedure.

1988 30' Weekender and have some stains on upper sides of vee berth. This caused by the forward quarter gunwales or stanchions leaking leaving a huge stain. I'm not sure what the material is and doesn't seem too damaged to the touch just the stain. Have removed the upper trim which showed a damp...

The amplifier was fine ended up needing to replace the ignition sensor in the distributor. This does not get high voltage so must have been due. Thanks for your input was ready to cut the check...

Hi all, 1988 30' SeaRay Weekender with 2x 260hp 5.7L's Mercruisers. I needed to run the engine without starting so I removed the wire from the top of the HT Coil. I noticed a spark from the center over to one of the terminals. After reconnecting everything I get no spark. Could I have fried the...

Thanks guys... The trim around the deck head trim are screws behind the buttons and at the back rest level there are actual nuts behind the back rests, I was a bit slow on that one. All came off fine. Thanks again...

1988 30' Weekender, Vee berth needs re-upholstering and trying to figure out how to remove the (what I call) back rest around the bed and the board that runs around the top. They have decorative buttons, is this where the fasteners are hidden? Any suggestions would be very helpful. Thanks -Dave

I'm looking specifically for anything that covers the alarm system. Starting up the engines this year I received an alarm on my stbd engine. It took approx 30 seconds for the audible alarm to sound and checking the gauges my temp and oil pressure are normal. After checking the engine after warm...

Can anyone help me locate an electrical diagram 1988 30 Weekender 2x 350 inboards. Many thanks .....Dave

Sorry guys, didn't realize everyone here are Sea Ray dealers! - LOL

Thanks for the diagram, good info. I hadn't thought about checking the tank grounding. Did you get my pm about upholsterer? Dave.

My layout is slightly different, mine has back to back seating and can be completely removed with no inspection covers. I will take some pics of area and try removing the air vents which are mounted to the rear of the tank. Even they seem to be an arms length away but then I will try to get to...

Thanks Wilee, They were prob trying to get the weight more forward. If you can check with you pal see if he has anything to add. Mike, An acronym, W-D? Also I really like the older 300's and their extra 2 ton. The newer were such an over all style change, they are times where I would change...