I have a 1988 30 Sundancer with the factory installed bronze seastrainers for the gennie and the A/C, but do not have a wrench to open them. I cant find info. on the manufacturer or a source for the wrench. I have been using a big pair of channelocks but would like to have the correct tool. Can...
This is a project I have wanted to do for a long time. We spend a lot of time on the hook, and I wanted a better way to read my battery voltages without going under the deck with a voltmeter. I used a 6 position rotory switch from Radio shack,I got the digital volt meter on e-bay for under $15...
:huh:Good morning. I am thinking on replaceng my old orig. battery charger. I run 3 group 31 batteries, and am wondering how many amp charger I really need? I have a 35 amp now, so its a little less than 13 amps per bank. but do I really need all that? I have kind of a tight budget. I see them...
I have a friend interested in a 1996 40 express. Are those boats cored hull? I have always had 80s sea rays with the bullet proof all glass construction, and cant offer him any help. :smt017 Thanx.
Hello. I have a Rayline remote spotlight. It all works, but when I'm underway I noticed it flopping up and down? Strange because it works fine both up/down and left/right, just seems to have some play in the up and down axis. Anyone have any ideas? Thank you.:huh:
Hey guys, I have a two piece set of factory snap in cockpit carpets in burgundy for a 268 Sundancer. These were for my 1987 268. They are in excelent condition. No rips, stains or burns. I will take a reasonable offer. Thanx, Dave:smt038
Hello to all. I'm looking for some information on 4 blade wheels. I have a 1988 sundancer 300 with twin 5.7 Mercs, with Alpha standard rotation 1.5 ratio drives, with 16X16 3 blade wheels. With the boat loaded, drives trimmed and 50 percent tabs, in aprox. 3 ft sea, she is turning 4600 RPMs...
Well, I have been putting off doing this project for a year, and today, jumped in with both feet. I tore out all or the mauve floor carpeting in my 300 sundancer. No real surprises. Some of the rug pulled right up, but most of it, I had to use a stiff sharp putty knife under it as I pulled it...
So, another boating season is approaching.......clocks get turned ahead this weekend! Got inside my rig today and started a list of stuff to do. What are all of the usual suspects doing to their boats this year?
I am looking for some waste holding tank dimensions and gallon size for an 80s vintage 30 ft sundancer that is equipped with a generator. My boat came with a SANX waste treatment system with a very small 7 gallon tank. I need to replace it with a larger capacity, but wanted to see what othes...
Does anyone know where the dockside pressure water fitting that is mounted on the starboard side of the cockpit, ties into the water system? I want to remove it, dont use it. I want to install a transom shower unit in its location. This is on a 1988 sundancer 300. Thanx in advance. Dave
Just wanted to see if there were any other certifiable classic sundancer lunatics out there !
I've had two, and just think they are great. This era dancer had a lot of bang for the actual size and money.
My first one was a mint 1987 268 Sundancer, one owner lake boat. We ran it for 5 years...
Hello. I am looking for some quidence on how to operate the SanX head tratment system. I was going to remove it and install a holding tank and macerator this year, but too many other important things to do. I have never used a vacuflush of sanx, and am looking for someone who has and uses their...
Does anyone know who makes, or where to find a folding transom seat supprt leg for an 80s Sundancer 300 ? This is the tubular aluminum leg, with plastic lock tab that hinges it, and locks it in the down position. Thanx Update: I found a better all stainless 13" locking leg from Garelic that...
Hello. I have just purchased a 1988 sundancer 300 that has a SAN-X treatment system connected to a Vacuflush toilet. Is this SAN-X system still a good system? Is it obsolete? I have tried to get info on a Google search, but does not give me much information. I have never owned a boat with...
Good morning. Has anyone ever removed the windshield frame on an 80s era Dancer? I have some corrosion issues that I want to address. I could sand, zinc chromate prime and touch the problem spots up, but it would never match, and not too mention, I would never be able to reach many spots. I...
Ahoy ! Does anyone have any ideas for restoring the color of the textured gelcoat dash on an 80s era Sundancer? Mine is a little faded. I have been told that pentrol would help, but am afraid of doing damage. Thanx, Dave