Search results

A friend of mine collided with a front bow pulpet on another boat and it stabbed thru the slider window / screen. Where is a good place to get replacments? Secondly are these hard to get out and service? The boat is a SRV-245 sundancer model.

We are detailing a newly aquired 85' SRV-210 and found the vinyl to have mold / mildew stains. We tried magic erasers, scrub brushes, krud kutter, and also bleach. None of which will take them out. Any sugesstions on which chemicals to use?

Looking inside the engine comparment, it appears the entire transom is only single thickness, then sea ray glassed in a double thickness only in the middle where the drive & engine goes. On mine the middle is firm and I can stand on the outdrive and there is little to no flexing. However where...

I need to know by tomorrow what I need to do if I plan to install a truck engine into an alpha one mercruiser. The old one is not fixable. Its a 350 chevy 260HP. Something about flywheels, starters, and mounting ears I seem to read about is what prevents people from swapping.

Looking at a 1978 SRV 190. Has a new (reman) L6 165HP engine, has newer front seats in it, nicely polished gel coat. Comes with legal trailer. Has some type of canvas but the guy has not had it up so we can guess it is incomplete or damaged. Not sure.... Guy states he had a new engine...

I know many will state this is not worth the effort, but why not. The back transom end is easy, no alterations needed. The front engine mount needs replaced further up and re glassed in. How involved is this? How good of quailty does this need to be tied into the stringers?

Need to check a quick value. Below is a list of issues. You may recall my two threads on this boat. Today I finally got it on the water which was a total bust. Short and sweet, here is what is wrong: -Transom moves quite a bit when you pull up and down on the drives. -Starboard 470 engine...

My 26' sea ray has a black judson engine syn on the dash and it appears to look kinda like a timing light. Any idea how it works or how to use it? I cannot find any info on it using the internet search.

Got the boat home, installed new batts, fresh oil, fresh 50:50 coolant, lower unit impellers, lube, trim fluid, and made sure blower, bilge pump, and electric is good. Anything else to do before a sea trial? Boat is unknown to me, and don;t want to blow anything up.

Just picked it up at a car auction. Won;t go into the boring details but bid on the wrong one and am stuck with it. http://community.webshots.com/album/580196384aPstiD Can someone tell me a little about this beast. What kind of cruise speed would be a close estimate and also wide open...

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&item=300433181217&ssPageName=STRK:MEWAX:IT If it had a good engine and a good trailer, what would this beast be worth? I am looking at this very same model locally.

Folks, What is the difference between a sundancer and weekender? Also specifiacally a 1981 245 Sundancer. How fast for cruise speed @ 3200-3500 rpm, and of course the max speed. It is a 350 merc 260HP.

Here is the pic of the manifold I need: http://outdoors.webshots.com/photo/2424007650044425697IIRBhz Here is a pic of my cylinder head arrangment: http://outdoors.webshots.com/photo/2352795840044425697LvhkPv The problem is, apparently the 6 bolt version of this from back in the 70's with the...

I weighed mine today with a total of 2500 pounds. I have not yet subtracted for the battery or the fuel. I already weighed the trailer so I subtracted that. I need a spec of dry weight, or if you had yours weighed. BTW I have the 4cyl 120 HP power plant. I need to do this to find out if it is...