Search results

Just replaced mine last week with the attwood ss model ( 6 gal ) $345 on ebay. Did not have room for the 11 gal. It was a long job , the whole vacuflush system had to be removed as well as the riser. I also had to remove 1 battery to get to one of the water lines. Very doable , just take your time.

No Matt did not have to remove anything, but it was tough getting in between them. Mine was running very slow, getting worse by the day. Then just stopped. Was able to hear it trying to open , but wouldn't. Figured if I am going to go through the trouble to remove it and try to clean it and then...

Just to let others know, I found the exact replacement from Danaher Motion. Can't buy direct, $425 from a local distributer. Wasnt fun removing the old one.

Can anybody tell me how bad it is to change the actuator on a 330. It looks real tight in there. Do the risers and manifolds have to come off? When I get the new one, will the wiring be the same as the old. Thanks for any input, I'm really dreading this job.

not sure which model I have, looks like two pieces. how can I tell which model it is ? The boat is old its a 1999. Hopefully its the ultra III

Thank you for the play by play. I have to do the same exact thing to the hatch on my boat. Couple of questions, do you have to remove the interior part of the frame..the part up against the headliner? Also what was the cost for the replacement arms ?

Hello my name is Chris , I have an '99 330 it has a broken u-line sp-18 . Do you think it will fit my boat? Do you have pics and measurements. Thanks

What is everybody doing for sirius radio ? I have the stock clarion unit. I have tried to hook up the portable unit from my car, but the clarion won't let me lock in a station to transmit the sirius. It only scans and locks into a station that already plays music . I'm sure there are some units...

I have an older 330 , will the same pigtail work on my engine hatch lift ? anybody with a picture of the set up? I'm not sure what it looks like,my boat did not have one.

I to will be needing a fridge replacement. Everybody keeps talking about the novakool 5810 model, does anybody have any pics of the unit in a 330da ? Where's the best place to buy it and how much is everybody paying for the unit ?

Can anybody recommend a good local carpet guy on the south shore around the patchogue/bellport area.

Welcome aboard Kirk. What make or model fridge did you get , and how bad was it to install?

can anybody tell me how to get to the fuel sending units . The starboard side and the port side as well. Is it possible that there can be almost 1/2 tank difference between the two tanks ?:huh:

todd, the gaskets ( grooves on the outside also )that came with the screens seem to big for the screen . How did yours fit ? Were they loose or were they snug ?

I just received my new screens and rubber gaskets from bomar. I'm not sure how they get installed. The big gasket is round (seems to big for the screen) and has a channel all the way around.

Just received my new screens from bomar today ( p-100-04 retro ), not exactly sure how to put them in . They sent me 4 screens and 4 big rubber gaskets that have a groove all the way around with an adhesive strip on one side. Can anybody explain how they go in . Its looks as if the gasket is to...

Is it normal for the fresh water pump to randomly kick on if the water is not being used ? It may run for 30 secs. to a minute, then shuts off . I don't remember it doing it that last year , anything I could check ?

is the ice maker still for sale ? Is it a u-line sp-18 model ?

Todd , I have a '99 330 that needs new porthole screens , can you please tell me where you got the kits from and maybe a part #. My wife keeps hounding me to fix them but I don't know were to begin. thanks

I have the 7.4 mpi fresh water cooled motors, can somebody tell me where the pencil zincs are located so I can change them . Does anybody have any pictures of the location on the exchanger . How about a part # from boatzincs .com...