Search results

  1. dan313

    Bilge water under the trash can

    I had the same issue on my 270AJ. The port running light was leaking. I know of at least 3 other 280 with the same issue. Good Luck.
  2. dan313

    2007 Amberjack..how do I remove this cushion??

    Lazy Daze, No grommets that I can remember. Screwed into the bottom of the pad. The boat is wrapped for the winter otherwise I would have taken a picture.
  3. dan313

    2007 Amberjack..how do I remove this cushion??

    To remove the back rest. you have to lay down on the deck and look at the bottom of the pad. You will see screws that hold the back rest in place. Remove the screws and tap the bottom of the back rest with your palm and the back rest will then come off. 5-minute job.
  4. dan313

    2007 Sundancer 260 - got fuel, no plane

    A guy on my dock just had the same issue. The cool fuel module was the problem and had to be replaced.
  5. dan313

    6.2L not reaching maximum RPM's.

    According to the tec sheet. I should get 5000-5500 rpm's out of my 350 mpi 5.7 mercruiser and get 40 mph. The best I can get is 4300-4500 on a good day and 32 mph. I just had a new long block put in. same 5.7 and all I get is the same numbers. I think it has a lot to do with the way the drive is...
  6. dan313

    Absolutely frustrated with this Mercruiser engine

    I had the same issue. Turned out it was the cam shaft positioning sensor. Its located in the distributor. 5 minute job to replace it.
  7. dan313

    Fiberglass repair needed LINY

    Thanks Guys. I contacted Raybo and sent him photos of what needs to be repaired. I am waiting for him to contact me. I also spoke with two others, and am waiting for them also. I will contact South Shore this week as well as Gulf. Thanks Again
  8. dan313

    Fiberglass repair needed LINY

    Good Morning, I am in need of a fiberglass guy who can repair my swim platform. I am located in Nassau County. Any recommendations would be appreciated. Thanks
  9. dan313

    2 bbeps every 2 minutes

    Its the water pressure sensor. 5 min fix. This happened to me and two of my dock mates. Unplug it and remove it. Put you finger over the hole where the sensor goes, some water will come out. Install the new one and be on your way. Its located on the back of the motor on the power steering tube...
  10. dan313

    350 mag mpi cut out at 3700 rpms

    This is the part number that I replaced Notes for Part Number #6 8M0156229 --SENSOR, Hall Effect, Camshaft Position
  11. dan313

    350 mag mpi cut out at 3700 rpms

    Update: It turns out the cam shaft position sensor was the problem. Changed it out and all is good. Lenny
  12. dan313

    350 mag mpi cut out at 3700 rpms

    My 05 350 Mag Mpi 300 hours on a rebuilt cut out at 3700 rpms like I turned the key off. The motor hiccupped one time but kept on running smooth. And after a while it just shut off and would not restart. Got towed back to the dock and started to check things over. I managed to get it started by...
  13. dan313

    350 mag water leak

    This same issue happened to a friend of mine. It was leaking at the blue plug. He tried a stainless plug and it made it worse. Turns out the Water Distribution Housing had a crack. Changed the housing all good now.
  14. dan313

    Bravo3 zinc anodes Sierra Vs Mercury

    I always buy aftermarket zincs off of Ebay. Never an issue.
  15. dan313

    Bikini forum due to popular demand

    Good Morning Boys....
  16. dan313

    Retired!

    Congratulations and welcome to the best club ever created. Remember one thing. Everyday is Saturday except for Sunday. And then its Saturday again. Enjoy every minute of it.
  17. dan313

    Selling my 2003 280 Sundancer

    What's your asking price?
  18. dan313

    Official 270 Amberjack thread (2005+)

    Crossr1, You were spot on with the way the boat handles. Its a chore to drive this boat at times. I said it once and I'll say it again. Its a lake boat at best. Where I boat on LI it's very congested on the water. Some day are better than others. I try to go out during the week (less boat...
  19. dan313

    Exhaust Manifolds causing water ingestion?

    I had that happen to me. I had 3in spacers and had to add 4.5in spacer to prevent that from happening again. My risers are now 7.5 in high. On certain boats the motor sits too low in the water and you have this issue. Hope this helps.
Back
Top