Make sure you are"logged in"and try"refreshing" the page.
Pictures are stored on an outside website and with this forum sometimes that has to be done to see them.
Not sure why.
Just sharing the thread transom repair thread I started.
Pictures near the beginning show a few signs of what to look for.
http://clubsearay.com/showthread.php/23289-1985-SRV270DA-Restoration
As a note this damage was started from previous owner not resealing swim deck and trim tab fasteners...
Surprises like that are no fun but it sounds like you have it under control now. Share some pictures if you can.
On the bright side it's a New Year and can only get better from here eh. :thumbsup:
Just sharing a response I had given to another windlass thread 3 months ago:
No response so I'm posting what I did on our 85 270DA for ideas:
On ours I took the anchor locker hatch away and replaced the existing pulpit with a longer one covering the opening. To securely attach and spread the...
We installed them on our race boat along with the oil pan drain hose so we pumped oil out of the drain plug when changing.
Easy install. Different styles available, some mount to the exhaust manifold riser and some can be mounted to a bulkhead or other surface.
Digging in the garage I had found i used that same Dow Corning sealant for bedding -worked great.
First step is the same for bedding side windows but there is a rubber spacer/gasket that pushes the panel (from the inside) against the frame and fills the gap.
I have removed an re-bed our 270DA side windows. Pull out the black rubber strip on the outside to access the screws. Not sure if it was done before by the previous owner but our screws were through the deck with nuts on the inside. I replaced them with new nylock nuts and off course needed a...
Not yet. We have had a very long heavy downpour and i saw water running down the wall about midway forward and under the storage compartment.
I did notice the sliding door was damp and expanded from moisture, not sure if that was just because of humidity from being closed and the leak.
It could...
Welcome Aboard!
Been there with the hitting head issue but it's only been when I'm in a hurry checking on it at the marina and I don't slide the cabin entrance hatch all the way open - every dang time I forget it's not open and crack my head on the way out. :smt101
Harsh Captain - I trip and...
Been there with the bouy trick in rough seas - gets old but still better than pulling the anchor up by hand.
Not sure if your locker is bigger than our 270DA but 450' might be difficult.
We are pushing the limit with the 30' chain and 300' rode. 99% of the time there is no issue but I have had...
The new teak pulpit was made by Ship Shop Marine Carpentry in Fort Pierce Florida (772-215-9925). They did an excellent job for about half the price I found anywhere else in the country. I finished it with 5 coats of Epifanes Wood Finish Gloss.
Thanks. I have to unlock the chain safety latch I...
No response so I'm posting what I did on our 85 270DA for ideas:
On ours I took the anchor locker hatch away and replaced the existing pulpit with a longer one covering the opening. To securely attach and spread the windlass load; I used (3) bolts through the deck with a backing plate and (2)...
Glad to be of assistance, the more we can share together here the less of a learning curve we all have to follow.
I know have another leak puddling on the starboard side in the back corner of the mid bunkroom.
Thinking it's the windshield up above because I cannot trace any path of where it's...
You are welcome.
Post pictures of your progress in the " Official-(1982-1988)-270DA-Thread " I'd like to watch how your coming along with your work.
Best of luck eh!
I posted the pictures taken in the 270DA thread to keep the collection together.
They are near the end of page 23, here is a link: http://clubsearay.com/showthread.php/52504-Official-(1982-1988)-270DA-Thread/page23
Re: 86 Da 270 entry way sliding hatch / 3 piece. Material question
Originally Posted by 86 Sea Ray 270
Ok here is the story just purchased my 1st Boat a 1986 DA 270. The boat is a handy man special, oh boy that means a lot of work, so let's get started. I am trying to repair the sliding...
I'll try to remember to take some snapshots for you in the next few days.
The sliding cover is basically one piece on top with two that fold out to cover the angled portion of the opening.
I would just make it out of formica covered marine grade plywood like you said.
Hard to tell what the...