Search results

I honestly have to say that I wanted to love this video, but instead I am furious and sick about it. For a trip(s) that could have been used for scientific purposes (don't know what exactly, but I'm sure someone could have come up with something useful), instead a group of people who must have...

Howdy All, We finally relocated to MB and are loving it. Looking to join a power squadron in the Myrtle Beach area. Would like to get to know some fellow boaters and get familiar with the ICW waters. Any & all feedback would be appreciated! PS: anyone going to Little River on Nov 30th for...

Next Monday 10/11/13 is Veterans Day. Applebee's & Golden Coral will be serving free meals to all veterans. They are posting different times when you can come in. The Golden Coral here in Myrtle Beach is stating to come in after 1600hrs (4PM). I will be there & hope to see & meet some...

I have 2 (two)1988 Mercruiser Alpha1 Gen 1outdrives. New water pump upper & lower housings 2013. New universal bearings 2010. 1.47 ratio is for a V-8 engine. I am piloting the boat to South Carolina and decided to put NEW drives on. That is the only reason for the swap. These drives are fine...

That makes sense. Thanks for the answer

Howdy All, Quick question. If an 5.7 Mecruiser (GM) engine is at 3000 RPM what RPM is the outdrive (alpha 1/1) turning at with a 1:47 ratio? It's been a long time since I posted here. With Irene in 2011 & Sandy in 2012 it's been a long tough time getting things back to normal (semi)! I...

are they inboards or I/o's you can look at the props and if the pitch is the same on both props they are probably both right hand rotation engines

Received mine last week, Thanks Jim http://i752.photobucket.com/albums/xx164/01ram2wd/IMG_3905-1.jpg

Thanks both of you guys. That was the first thing I did. All were the newer rubber type but as I had it appart I changed them anyway

Howdy, I have a weird noise from my port engine. Kind of like a "rattling" metalic sound. Sounds like something is loose & rattling. Checked everything, all is tight. Looked for the grease fitting on the engine coupler and there is none? Any help would be appreciated.

I remove mine every year, store in the garage (heated) & change the impellers. Well worth the $100.00 each season. You can buy stands or make your own!

WOW! I'm glad I have more than one hobby.

Check out Drunken Jacks Great seafood

Old Vet If your alignment is off the outdrive would not reinstall back on. The alignment is only needed if the gimbel bearing was replaced or fiddled with while the drive was off.

Howdy, Get it out of the water ASAP If you are sure it's flowing bow to stern that would rule out the bellows and most other connections to the rear. Do you have a seacock @ your head. Any other thru-hull fittings below the water line. Pull out all your cabin cusions and look at the...

I'm using a 10" netbook and Diginav w/Gps ant. Also have 8,000 songs, can transfer my digital photos in minutes & watch Dvd movies for under $300 http://www.diginav.us/

it was posted here a couple months ago...so i saved it!

I don't have a wiring diagram but here are the color codes... Blk -Grounds-General Blk/Brn -Pump Grounds Blk/Red -Voltmeter Grounds Blk/Org -Isolated Accessory Grounds Blk/Yel -ignition stop Blk/Grn -Water Level Sender Ground Blk/Blu -Lighting Grounds Blk/Gry -Nav Light Grounds Blk/Wht...

I'll try that now. thanks

Yes, used same boots and are pushed on as far as they will allow.