Recent content by tmo_7

Yes, this is same boat as boater2018, with the exception of a few engine components. I wanted to be able to pull a heavy skier on slalom, which the new 17p 4-blade prop does better in this area. Last year, we pulled four skiers at the same time with no problems. Also, low-speed tracking seems...

My boat is a 2000 210SD with 5.0 EFI 240 hp and Alpha 1. It has a 1.62 drive ratio. A few years ago, I tested and recorded conditions, top speed, and engine tach rpm. This is just FYI. 1) 19p Mercury Vengeance stainless 3-blade prop, 14" x 19p: Tested full throttle top speed on smooth water. 2...

Dennis always has good solutions. I recently purchased the camper enclosure for my 2000 210SD. I followed SeaRide's instructions in the post linked below, which worked great for us. One key point is that you will have to extend and retract the rear bimini poles. The panels work great on this...

FYI: I repaired a loose wire on the external speaker which is connected to the depth sounder. Problem solved.

Thanks, Henry. I have seen some used & NOS 3500's on eBay...before my problem started. Hoping someone on the forum may part with one after an upgrade.

My Lowrance 3500 depth finder audible depth alarm / speaker is intermittent. I would like to replace the display / head only, and re-use my transducer and cable. The display works fine, but I rely on the audible alarm for shallow water. Please let me know if you have one to sell. Thanks!

This trailer is listed around Lake Lanier, north of Atlanta. It may be a bit overkill, but I have seen 260SD on triple axle trailers before. 2008 Load Rite Elite 3 Axle Boat Trailer - $3499 (Lake Lanier, Port Royal Marina)http://atlanta.craigslist.org/nat/bpo/5154552674.html

The same part (pawl) broke / sheared on our new 2012 ShoreLand'r trailer after only a few short hauls. A quick call to ShoreLand'r / Midwest Industries, and they shipped a complete winch assembly, no questions, no cost. I could tell by the conversation that this was a common failure. This is an...

Please read my posts from 2014 on this subject. My motor is 5.0 EFI, 300 hrs. I believe I had the same symptoms you are experiencing. Merc insisted on replacing the ECM fo ~$4k. Another mechanic found root cause was faulty ignition coil. Mine had no issues with rotor, cap, plugs, or fuel...

I replaced the OEM four blade 19p SS prop with a Hill Marine / Signature 14 1/4 x 17p four blade SS prop. I have noticed some improvement on hole shot, low-speed tracking, pulling/ watersports. I would recommend this prop for this boat / motor setup. However, I have found that the old adage...

We have a different boat, similar problem. I added a 9 inch grab handle from Flounder Pounder. The appearance, diameter, ends, look the same as the OEM center rail. It has worked great while climbing the ladder. I have tried to include a picture.

Send me a PM. I have an extra cushion that came with my boat. Let me know your vinyl & trim colors.

SunDecker: did you already look at this steering wheel cover? Or maybe you only need the top grab section? http://m.ebay.com/itm/400170018990?nav=SEARCH Greatlakesskipper: SEA RAY SPORT WOODGRAIN BOAT STEERING WHEEL COVER

I have five asymmetric grab handles, and one symmetric handle (engine box). All plastic/rubber outer layer, in off-white color. No mold/mildew. We can work something out on these OEM plastic/rubber handles if you are interested. I replaced these with stainless grab handles from...

Check Bristol Upholstery, http://www.1888boattops.com/Searay.html I bought some vinyl for our 2000 210SD (seat bolster) and it matched perfectly. Sea Ray cust svc can provide the part number / color, or you can check the boat's parts manual. You can find the manual on the internet.