I get the same fuel economy at the same speed. It runs great when its light on fuel, but it squats with a full tank and I need to really push it hard to get the bow to drop down. If I push it to 3900rpm, the bow will stay down with very little tab. The hull performs well at 24+ mph, any...
I bought the igloo model at Costco. It works very well. We go on two week trips often and we never have a need for ice. It takes about 24hrs for it to get cold, especially with warm beverages. The power drawer is extremely minimal. I had it on my other boat for 3 days on a single deep cycle...
Again, thanks for the replies. The boat has 500 hrs, 250 hrs are from me. I have owned the boat for 4 years. I had the hull surveyed when I bought it. 2 years ago I had the bottom media blasted and barrier coated and repainted (It didn't need it, but I'm a finatic) I had the props balanced...
Thanks for the replies. The boat is miserable to run under 3800rpm @ 24mph. If I run slower I am squatting and throwing a huge wake with the tabs buried. If I run up in the higher rpm and speeds I can pull the tabs up and the bow will stay down.. As soon as I pull the throttles back to run a...
I am thinking about putting larger tabs on my 2003 320 DA. I have to run it pretty hard to get the bow down. I have V-drives and I have to run at 3800-4000rpm to get the bow down.
I see some fellow owners/members concerned with navigating Moriches. The Moriches Inlet is OK at best. It can be a bit tricky, but there is an east and a west cut. They can be hard to see from the ocean side. From the East you need to stay right on the tip and head into the middle and once...
I was looking at your problem and it sounds all too familiar. After running at 1000 rpm pull your spark plugs out. You may have water getting into your combustion chamber. I had a similar problem after replacing my exhaust with aftermarket Sierra exhaust and one of the manifolds where...
Hey Russ, it Anthony, we met at Watch Hill. We had a good time with you guys. Ive been shopping for my new sound system, your is awesome! Where did you buy the JL speakers? I can't find them. For less than $280 a pair. After seeing your camper top, we had our canvas guy at our house on...
I used a clear "anti-foulant" on the lower unit if my yamaha outboard and it looked alot like that after it came out of the water. It may be something the previous owned tried on the drive and removed it from the easier surfaces.
New hampshire insurance company.
I pay 420 for the year. I have a 1000 ded. Im covered for 85,000. I also get a small discount for being a Capt. But its only a small percentage. Good luck!
If the engine is hydrolocked it means that there is water in the upper half of the engine. Pistons travel up and down in the cyl, compressing air and fuel... It then fires when it is on the combustion stroke.
If you get water in the cyl, it cannot be compressed, therefore it is locked...
Thats boating! We are lucky to have forums like this to get information based on other peoples experiences. By the time your done with this you'll be a pro...Talking the talk and walking the walk.
If you have some time look at Jasper engines. They are great reman engines.
Sounds like your on the right path. I would take the belt off and make sure all the accessories are spinning freely. Pulling the drive is a good idea anyway. It may just be a gimble bearing that is locked up.
If you free rev the engine do you have noise? If you put it under a load if its a slow bang is more than likely a drive issue. Take a look at the fluid and look for metal. If the boat was put away with water in the lower unit it may have pitted the bearings causing them to let go. Try runing...
The manifold is the exhaust part connected to the engine. The riser is inbetween the manifold and the elbow. If the are original they will probably have stickers with serial number for engine on them. You cant see if they are bad by looking at them on the engine. You need to pull them off...