Lazy Daze
Last Activity:
Dec 3, 2021 at 5:47 PM
Apr 21, 2009
Likes Received:
Trophy Points:

Share This Page

Lazy Daze

Well-Known Member, from PA

TECHNICAL Contributor GOLD Sponsor
Lazy Daze was last seen:
Managing account details, Dec 3, 2021 at 5:47 PM
    1. Sesler
      I need a picture of the routing of the water hoses from pump to block on a 1998 sea ray express cruiser
    2. serig
      Can you help me? We are looking for part number 1801355 (vent cover) for our 2007 195 sport; starboard side.
    3. Chris Caley
      Chris Caley
      I recently purchased a '97 Sundancer 240 with a 5.7 w/ Alpha one drive. I am replacing the engine, adding a few HP, and I am going to replace the outdrive as well. My immediate problem is not knowing what the gear ratio is for this outdrive Frankly, there is a lot of stuff I don't know about this boat. Does anyone know what the ratio might be, and who is a reputable dealer from whom to purchase the hardware?
    4. Klaus Leopold
      Klaus Leopold
      Hi! I am looking for a boat certificate or even better "boat stability test" for my Sea Ray Sundancer 340 (2008). Can somebody help or know where to get? There is as good as nothing on the boat.
    5. tacoma4251
      Hi Lazy Daze,

      I'm a new boater owner of a 1999 240 Sundancer. I want to charge the batteries (3) using my shore, home ac power. My battery selector switch has 3 positions.....What position should it be on? Also, do I need to turn both the AC panel on and the Inverter switch on?

      Thank you ahead!
    6. tacoma4251
      Hi Dennis:
      There's a selector switch located inside a cabinet with a clock like face in the rear of the boat. The switch has 4 positions: 12, 3, 6, and 9 o'clock. I need help figuring what position the selector switch should be in when starting, when boating on the lake, when parked in the driveway, and when charging the batteries?

      Thank you!
      1999 240 Sundancer
    7. marks737
      Hi Dennis. I saw your post from last year on the 3way quick disconnect fogging modification for MPI engines but I couldn't see the diagram or photos. Any chance you could email them to me? I would greatly appreciate it.

      Mark Smith
    8. NorCalGlenn
      Thank you Dennis!
    9. NorCalGlenn
      Hey Dennis! I am installing my gps puck on Friday, and need to drill a 1" hole on my deck at the base of the windshield. I was wondering - do I just use a regular drill bit for that? Any advice is appreciated! glenn
    10. Adam1

      What do you recommend to use for reseating and sealing the Drain Plug Flange? I recently used 3M Marine Adhesive/Sealant Fast Cure 4000 UV. It forms a firm, rubbery waterproof seal. Its flexibility allows for the dissipation of stress caused by shock, vibration, swelling or shrinking. Designed for marine applications above and below the waterline. I'm concerned however that the flange will bond strongly to the fiberglass preventing me from one day having to remove it. Is this a valid concern with this product? Should I have used something else?

      Thanks in advance for your thoughts and advice.

    11. Siskin
      Hi Lazy daze,
      i looked for the two wires but can't find any. not sure where they would be at. do you know where i can get a wire diagram from the switch to the pump?
    12. rcknecht
      Dennis, I have a neighbor looking for a used fresh water boat with no bottom paint... No trailer needed, about a 25' DA... Please send me your contact info at Peter's so I can direct him your way...
    13. Lazy Daze
      Lazy Daze
      Merc changes recommendations from year to year - I don't know why. Check your owner's manual to be sure, but it may recommend 100 hours or end of season (whichever comes first).

      Aside from that, is this your first year with the boat? Normally I would say you'd be fine to wait a bit, but in this case (if your manual says - not the dealer - 20 hours) I'd recommend doing it right away. I doubt this would, in reality, happen, but you could get yourself into a warranty denial scenario.

      Hope this helps,
    14. jmlloyd526
      You have helped me before so i hope you dont mind the pm. My 195 w/ 5.0 tks has 24 hours. How important is it that the 20 hour maintenence be performed on time. Can it wait til 30 or 40 or should i take the time to get it done asap? Thanks
  • Loading...
  • Loading...
  • About

    Boat Info:
    Boat Brand:
    See Signature


    1999 260DA, 2000 215EC, 1998 210BR, 1999 190BR, 2000 180BR. And a few others...
    1982 Grady 241 Weekender/Offshore 250HP Yammie OX66 (stern drive modded to be OB)
Show Sidebar