Recent content by jaiello@pseassociates.com

  1. J

    2000 Mercruiser 350 MPI Horizon fuel rail o-rings 25-862053

    If any of you have run into this problem I have a solution. Mercruiser discontinued the fuel rail crossover o-rings from their inventory. I rebuilt my engine but because of 8 o-rings I couldn't finish the job. Luckly, I'm in the rubber business so I sourced the o-rings from Apple Rubber in...
  2. J

    Running a new depth sounder transducer cable

    Does anyone know where the wire chase to the bilge is on the starboard side of a 2000 310DA? Im installing a new depth finder and need to run the cable into the bilge. THX
  3. J

    Leaking underwater exhaust

    Thanks. I think we hit something when bringing the boat up to CT from NY in May
  4. J

    Griddle for Kenyon glass top electric stove

    Has anyone found a griddle that works with a Kenyon glass top electric stove? I'd be interested to know who made it and where I can get one
  5. J

    4 blade prop replacement

    Has anyone replaced the standard 3 blade props on a 310DA with 5.7 Horizon MPI inboards with 4 blade props? Id be interested in the results?
  6. J

    Leaking underwater exhaust

    I have a 310 DA year 2000 with twin 5.7 MPI. My mechanic tells me we have a leak coming from the port underwater exhaust. Anyone have any info on how this part is attached to the hull and how to stop the leak.
  7. J

    Lost Power to Ignition

    I had something weird happen yesterday. After a great day on the water when I went to start the STB engine with the generator on the engine wouldn't crank. If I pushed the emergency start the engine would crank but not start. The port engine started and ran fine. When I shut off the generator...
  8. J

    V-drive

    I just purchased a 2000 310DA with 5.7 Horizon MPI inboard with V-Drives. Anyone know who manufactured the V-drive? I received no manuals with the boat.
  9. J

    Lofrans Progress 1 Windlass

    Inhad ad the yard mechanic install the repaired motor. He had to file the key so it would slide into the keyway. He also removed the rear motor cover so he could put a screwdriver on the slotted mounting bolts while he tightened the nuts
  10. J

    Lofrans Progress 1 Windlass

    Turning the gypsy does not turn the key slot because the clutch is not engaged. We have tried to align the key slot with the mounting holes on the gear box and then do the same with the key way on the motor. We have gotten the motor on but as soon as we let go to put on one of the 6mm nuts...
  11. J

    310 Sundancer Thread (2007 & newer)

    I just changed the broken upper track and I did remove the panel. I had to cut through the caulking to make the repair. I re caulked the joint with a regular exterior silicone caulk I got from the hardware store. It doesn't exactly match but it looks great. I used blue masking tape to keep the...
  12. J

    Barbecue grill for 310 DA

    I just purchased a 2000 310DA. I was wondering if anyone has used a barbecue grill. On my old boat I had rod holders and I mounted a Magma propane stove in the rod holder. There are no rod holders on the 310 and with the U seating there is only one place I can see to mount the grill. On the port...
  13. J

    Lofrans Progress 1 Windlass

    Easier said than done. The installation of the motor is blind and the only access is from the hatch which barly gives you room to get in to install
  14. J

    Atwood 6 gal water heater

    the 310 is a little different. The water heater is on the port side behind the vacuum flush generator and holding tank. It is under the port exhaust pipe next to the water lift muffler. I was hoping if removal of the aluminum extrusion that supports the port and center hatched would allow me to...
  15. J

    Atwood 6 gal water heater

    Anyone have any experience with replacing the Atwood 6 gal water heater in a 310 DA? Mine is a 2000 and the engine spaces are very tight. I'm interested to know what I have to take apart in order to get the old water heater out and the new one in. John Aiello
Back
Top