TN370
Active Member
I think you need 18" rather than 19".I found a deal on Nibral 4 blade 19X21 props, will these fit ? I don't want to pull to check
just wondering if any one has tried them out before
Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
I think you need 18" rather than 19".I found a deal on Nibral 4 blade 19X21 props, will these fit ? I don't want to pull to check
just wondering if any one has tried them out before
I'd like to do the same thing but not sure about our windlass. If you have the same one that came on my 95 the brand is Best. But that hasn't really told me of chain will go through it. Here's the rode I'd like to get if I could find out:Hi all you 370's
i need to change my old anchor line for new! just wondering if anyone knows if i can run chain through the windlass on my 96' 370 DA? It's the old style windlass and has 5/8" line!
Hi guys
I got the boat last summer
have a problem my actuator electric windsheild motor is missing . Is there anyone ho nows were i can get one
Boat is a 370 DA 1995 . Can anyone of you guys send me a picture or put it up on the forum so i can see what it looks like
hope my english is decent
Regards Torgny
Compare this picture:
http://www.370sundancer.com/1998/photos-2/#!prettyPhoto[gallery]/12/
with this picture:
http://www.370sundancer.com/1995/photos-233/#!prettyPhoto[gallery]/17/
The first is my boat which has the water lift mufflers and the other a 95 boat with the log style.
Gene
duckee, from 2014...can you repost the 2 exhaust pics? the links above won't work.Compare this picture:
http://www.370sundancer.com/1998/photos-2/#!prettyPhoto[gallery]/12/
with this picture:
http://www.370sundancer.com/1995/photos-233/#!prettyPhoto[gallery]/17/
The first is my boat which has the water lift mufflers and the other a 95 boat with the log style.
Gene
OEM spec is 18x21 3 blade! If you go to 4 blade you need to downsize to 18x20! I did the same this season, went to a 18x20 Nibral 4 blade! i think i like the 3 blade better, felt like i was getting more speed at the same RPM!I think you need 18" rather than 19".
OEM spec is 18x21 3 blade! If you go to 4 blade you need to downsize to 18x20! I did the same this season, went to a 18x20 Nibral 4 blade! i think i like the 3 blade better, felt like i was getting more speed at the same RPM!
I know but I can these for 500.00
19" x 19 a pair I just wonder if 19" will fit
It's important to make sure they are cupped blades. I'm finding out the hard way right now. Brand new 18x21s on and I've lost all speed. I'm topping out at 16 mph wide open. Swapping back to my old ones next week after there repaired and then sending back the new ones to have them cupped. Don't make the same mistake! The spec is 18x21 3BC. The 3BC means 3 blade CUPPED apparently...OEM spec is 18x21 3 blade! If you go to 4 blade you need to downsize to 18x20! I did the same this season, went to a 18x20 Nibral 4 blade! i think i like the 3 blade better, felt like i was getting more speed at the same RPM!
Hi all,
Hope anyone effected by the hurricanes is well and didn't suffer any damage. I'm just getting back to the forum after being out of the country for over a month and came back just before Irma came visiting here in Clearwater. Where it bad it could have been much, much worse. My sympathies to all who were hurt.
Have couple of question, one major & one minor.
a. For some reason both aft bilge pumps have ceased to work after Irma. I've active the manual switch on the dash and got nothing and cleared what little debris I can see since there's quite of bit of water up to and just over the base of the high water float switch. In fact I see lower float switch is all the way up. The fuse panel on the bulkhead doesn't show the red knob being tripped and the batteries are ok as the engines kick over right away. Before I go sloshing around in the tight space back there I could use some advise. My manual says there's supposed to be breaker on the DC panel but there isn't one. Is there an inline bilge pump fuse somewhere that may have blown or tripped?
b. Other minor question Has this Official 370 forum format changed? The last time I was on it back in Jul or Aug there were well over 200 pages showing but now only 135 plus the layout is different. Hate when that happens.
Spec for a 1998 (look on 370sundancer.com front page, I provided Gene with the specification sheet and drawing)I found a deal on Nibral 4 blade 19X21 props, will these fit ? I don't want to pull to check
just wondering if any one has tried them out before
I have a 96 370 Sun Dancer and the frig is about shot. I know someone has replaced theirs at some time. With this many messages I don't know how to search for this topic. So If you replaced yours please tell me what one you got and how difficult it was to do.
Also I am looking at doing the Great Loop in my boat and want to put in additional frig. The Ice maker is gone so that would be a great place to put one. If you have done that Let me know what one you used and if it was AC/DC or not.
I am also going to modify the Port seating to table top. Going to remove the Seat and make a table for cooking and or entertaining. Any thoughts on that?
I would also like to put in a freezer of some kind. any suggestions on where I would put it?
Thanks everyone for your amazing responses.
Barry[/QUOTE
Can't believe no one on here has any help or information for me. I am sure some of you have replaced the frig and done other upgrades that could give me some incite. Please!
Barry