New Profile Posts

  1. Christopher Mesker
    Christopher Mesker
    All fisherman are liars except for me and you, and I am not so sure about you!
  2. brewster16
    brewster16 Lazy Daze
    Dennis I just posted the question in the "Northeast" section but then I thought of you...Can you advise me on where I should go to get a professional rigging job to splice my anchor and new anchor line?
  3. brewster16
    brewster16 Lazy Daze
    Dennis I just posted the question in the "Northeast" section but then I thought of you...Can you advise me on where I should go to get a professional rigging job to splice my anchor and new anchor line?
  4. Bobby Whitehead
    Bobby Whitehead
    Looking for a tri-axle trailer to fit 88 SeaRay weekender 300,At least 10,500 pound capacity
  5. JTaylor
    JTaylor Two Sisters
    Do you still have the 20' Amberjack CC?
    If you do PLEASE contact me.
  6. Almightys
    Almightys Gofirstclass
    Im interested in the emblem. I don’t need a pic just tell me where to send the money. Thanks
  7. Hydraulicpro
    Hydraulicpro
    I just had to do it. I am a Veteran of the USN Nuclear Attack Submarine Silent Service Brotherhood.
  8. Clayt
    Clayt
    1994 Sundacer 290 owner. Need new lower shift cables. Twin 4.3L Need to know the correct cables.
  9. GhibliGod
    GhibliGod Capt. Rusty Higgins
    I was going through the site and saw you, I remember you I'm pretty sure. I was a guard at SeaRay Merrit Island for a little bit years ago
  10. Chris Wood
    Chris Wood
    Sundancer 310- The bolt from the engine hatch lift actuator and the hatch failed. Can I use a steel bolt or do I need a Sea Ray part?
  11. LivingTheDashIV
    LivingTheDashIV
    Need help with Parts!!!!!
  12. Jims65/23’
    Jims65/23’
    Buying this to restore, so far, was told it had one cracked exhaust manifold. Any suggestions? Thanks.
  13. Randy Coleman
    Randy Coleman 20pilot
    I’m searching for the actuator mounts that are attached to the underside of the engine hatch.
    The ones that the rams mount to for raising and lowering the engine hatch.
    Please let me know if available?
    Thanks
  14. carterchapman
    carterchapman Keith Zibilich
    Hey Keith - Thinking about you. Hope you are doing well after Ida.
  15. Mknupp
    Mknupp
    Need to replace my air conditioner water pump. Any suggestions on a replacement. 1995 330
  16. Gord
    Gord Stee6043
    Stee6043 I must ride by you all the time but I can not tell which boat is yours. We keep our boat in Grand Haven and are there most weekends
  17. Tri County Trail
    Tri County Trail Henry Boyd
    2005 Rinker 360 Mercruiser 496 Mag Bravo 3s Manual shift no smartcraft display
    no Smartcraft Architecture yet.
    So after researching this, I am looking for two cables to a J Box add a Vessel View 8M0115080 then can I connect to the simrad with blue tooth or do I need a cable from J Box to Simrad and leave out Vessel View 8M0115080. Any Help from the pros would be great!!!
  18. Tri County Trail
    Tri County Trail Mittens
    So after researching this, I am looking for two cables to a J Box add a Vessel View 8M0115080 then can I connect to the simrad with blue tooth or do I need a cable from J Box to Simrad and leave out Vessel View 8M0115080. Any Help from the pros would be great!!!
  19. Tri County Trail
    Tri County Trail Mittens
    Reading forums trying to figure out the correct solution, and you were so helpful to many, I thought I would reach out if you had time. 2005 Rinker 360 Mercruiser 496 Mag Bravo 3s Manual shift no smartcraft display
    no Smartcraft Architecture yet.
  20. Tri County Trail
    Tri County Trail scooper321
    Wondering If you have any insite to this.
    Part numbers required ect.
    Thanks for any help.
    So if I connect like in your diagram I can send the data thru canbus and directly to my Simrad Go 9 XSE. would not need vessel view?
    I believe I can update my software on my Simrad Just purchased Boat and trying to get both engine data and diagnostics.
Show Sidebar